16 Inch Chainsaw Chain for Craftsman CMECS600 / S165 / S160 Chainsaw

This 16 inch chainsaw chain is made as a replacement for specific Craftsman saws using a 16-inch bar. Based on the original listing, it fits Craftsman CMECS600, S165, S160, and CMXGSAMN4216 chainsaws, and the package includes 2 pieces of 16-inch chain.

Will this chain fit your saw?

Start with the simplest check: your saw should use a 16-inch bar. If your chainsaw is one of the listed compatible models — Craftsman CMECS600, S165, S160, or CMXGSAMN4216 — this is the intended replacement chain from the listing.

It is still smart to confirm the full chain spec before ordering or installing any replacement chain. Chainsaw chains are matched by four key measurements:

• Bar length: this product is for a 16-inch bar
• Pitch: the spacing between chain links
• Gauge: the thickness of the drive links that fit into the bar groove
• Drive-link count: the total number of drive links on the chain

Even when two chains are both called “16 inch,” they are not always interchangeable. A chain with the wrong pitch, gauge, or drive-link count may not seat correctly on the bar and sprocket. That can lead to poor cutting performance, chain derailment, or accelerated wear.

To confirm fitment, check one or more of these places on your saw:

• The markings stamped or printed on the guide bar
• Your owner’s manual
• The existing chain
• The model number label on the chainsaw housing

Compatible models and part references from the original listing:

• Craftsman CMECS600
• Craftsman S165
• Craftsman S160
• Craftsman CMXGSAMN4216

Package contents:

• 2Pcs 16-Inch Chain

If your saw is one of the models above and uses the original 16-inch bar setup, this is the replacement chain the listing is intended for.

Replacing the chain

Always replace the chain carefully and with the saw powered off. For corded or battery-powered saws, disconnect power first so the saw cannot start accidentally.

1. Turn off the saw and disconnect the power source. Let the bar and chain cool before handling.
2. Loosen and remove the side cover so you can take tension off the old chain.
3. Lift the old chain off the sprocket and guide bar, then clean sawdust and debris from the bar groove and cover area.
4. Install the new 16-inch chain around the drive sprocket and along the guide bar, making sure the cutter direction matches the normal forward cutting direction along the top of the bar.
5. Reinstall the side cover and adjust chain tension so the chain sits snugly in the bar groove but can still be pulled around by hand with a gloved hand.
6. Recheck tension after a brief test run, since a new chain may settle in quickly.

A chain that is too loose can jump the bar. A chain that is too tight can overheat and wear the bar, sprocket, and motor more quickly.

Keeping it sharp

A sharp chain cuts faster, runs cooler, and puts less strain on your Craftsman saw.

• Keep chain oil topped up if your saw uses bar and chain lubrication. Proper lubrication helps the cutters and drive links last longer.
• Touch up the cutters regularly instead of waiting until the chain becomes very dull. Light, frequent sharpening is easier than restoring a badly worn edge.
• Clean the bar groove and inspect chain tension often, especially during the first few cuts with a new chain.

If the saw starts producing fine dust instead of chips, pulls to one side, or needs extra pressure to cut, it is usually time to sharpen the chain or inspect the bar.

FAQ

Does this chain fit all Craftsman 16-inch chainsaws?
No. It is listed specifically for Craftsman CMECS600, S165, S160, and CMXGSAMN4216. A 16-inch bar alone does not guarantee fit, so confirm the chain specifications on your saw.

How many chains are included?
The package includes 2 pieces of 16-inch chain.

Can I install this chain if my old one is missing?
Yes, but you should verify your saw model and the bar’s printed chain specifications first. Matching bar length, pitch, gauge, and drive-link count is important for safe operation.