2PC 10 Inch Pole Saw Chain for Milwaukee 49-16-2720

Fitment overview

This 2-piece 10 inch pole saw chain set is made as a replacement for the Milwaukee 49-16-2720 Pole Saw Attachment and the Milwaukee M18 FUEL 10 in. pole saw models 2825-21PS and 2825-20PS. It also replaces Milwaukee chain part number 49-16-2723.

If you’re shopping for a replacement chain for one of those Milwaukee 10-inch pole saw setups, this is the fitment these chains are intended for. The most important starting point is matching the saw and bar size correctly before installation.

Will this chain fit your saw?

This chain is listed as fitting the following Milwaukee pole saw models and part numbers:

• Milwaukee 49-16-2720 Pole Saw Attachment
• Milwaukee 2825-21PS M18 FUEL 10 in. Pole Saw
• Milwaukee 2825-20PS M18 FUEL 10 in. Pole Saw
• Replacement for Milwaukee part number 49-16-2723

To confirm fitment on your specific saw, check these four items on your current chain or bar:

• Bar length: this replacement is for a 10-inch bar
• Chain pitch
• Chain gauge
• Drive-link count

The bar length is already known here: 10 inches. That makes this a match for the Milwaukee 10-inch pole saw applications listed above. For the other chain specs, the best practice is to compare the markings on your current bar or chain, or verify against your saw’s manual or original replacement chain packaging.

Why that matters: even if two chains are both labeled 10 inch, they can still differ in pitch, gauge, or drive-link count. Those dimensions must match your bar and drive sprocket for proper operation. If your saw is one of the listed Milwaukee models and your existing chain corresponds to Milwaukee 49-16-2723, this replacement is the intended fit.

A quick way to avoid ordering the wrong chain is to check for both:

• one of the compatible Milwaukee model numbers above, and
• the replacement part reference 49-16-2723

If both line up, you’re on the right track.

Replacing the chain

Before replacing the chain, remove the battery or make sure the power source is disconnected. Pole saw chains are sharp even when dull enough to cut poorly, so gloves are a smart idea.

1. Remove the battery and place the pole saw on a stable surface.
2. Loosen the side cover and release chain tension according to your saw’s normal adjustment method.
3. Remove the old chain from the bar and drive sprocket, then clean debris from the bar groove and sprocket area.
4. Install the new chain in the correct cutting direction, making sure the drive links seat fully in the bar groove and around the sprocket.
5. Reinstall the cover, adjust tension so the chain sits snugly on the bar but still moves freely by hand, then tighten the hardware securely.
6. After a brief test run, recheck chain tension and adjust again if needed.

A chain that is too loose can derail. A chain that is too tight can wear the bar, chain, and drive components faster.

Keeping it sharp

A sharp pole saw chain cuts faster, throws cleaner chips, and puts less strain on the saw.

• Avoid contacting dirt, rocks, metal fencing, or the ground. Even brief contact can dull cutters quickly.
• Keep the chain properly tensioned and make sure bar oil is reaching the chain during use.
• Touch up the chain early rather than waiting until it becomes very dull. If the saw starts making fine dust instead of chips or requires extra pressure, it’s time for service.

Because this is a pole saw, many cuts happen overhead or at awkward angles. Taking a moment to line up the cut cleanly can help the chain stay sharper longer.

FAQ

Does this fit all Milwaukee pole saws?

No. This chain is specifically listed for the Milwaukee 49-16-2720 Pole Saw Attachment and the Milwaukee 2825-21PS and 2825-20PS M18 FUEL 10 in. pole saw models. Always confirm your model number and chain specs before installing.

Is this a replacement for Milwaukee 49-16-2723?

Yes. This chain is listed as a replacement for Milwaukee part number 49-16-2723. If your current chain or manual references 49-16-2723, this is the matching replacement type for the listed 10-inch Milwaukee pole saw applications.