Replacement chain fitment for Black & Decker LCS1020 and WORX WG322
If you need a replacement chain for a Black & Decker LCS1020 or a WORX WG322 cordless chainsaw, this Opuladuo 10-inch chain is intended for those saws. It’s a practical choice for routine replacement when your original chain has become dull, stretched, or damaged from normal cutting.
Because chainsaw-chain fitment depends on more than just bar length, it’s still worth taking a minute to confirm the specifications on your saw before ordering.
Will this chain fit your saw?
This chain is listed for the following models:
- Black & Decker LCS1020
- WORX WG322
The listing also describes it as a 10-inch replacement chain. That’s the first thing to verify, but it should not be the only thing you check. A chain must match all of these:
- Bar length: 10 inch
- Pitch
- Gauge
- Drive-link count
Even if two saws both use a 10-inch bar, they may not use the same chain if the pitch, gauge, or number of drive links is different. The safest way to confirm fitment is to compare the markings on your current bar or chain, or check your owner’s manual for the exact chain specification.
A few quick ways to confirm:
- Look on the guide bar for printed chain specs
- Check the existing chain packaging, if you still have it
- Compare your saw model directly: Black & Decker LCS1020 or WORX WG322
- If replacing an original chain, make sure the new chain matches the old one in all key dimensions
The original listing mentions compatibility with a variety of chainsaw models, but only the model numbers above are specifically provided. If you have a different saw, do not assume fit just because it uses a 10-inch bar.
Replacing the chain
Replacing a chain on the LCS1020 or WG322 is usually straightforward, but always work carefully.
- Remove the battery and make sure the saw cannot start accidentally.
- Loosen or remove the side cover so you can take tension off the old chain.
- Remove the old chain from the bar and drive sprocket, then clear away built-up sawdust and debris around the bar groove and sprocket area.
- Install the new chain in the correct cutting direction, seating it around the sprocket and into the bar groove.
- Reinstall the side cover and adjust chain tension so the chain is snug on the bar but still moves freely by hand.
- Reinstall the battery only after everything is secured, then check tension again after a brief test run.
A new chain can stretch slightly during early use, so it’s normal to recheck and retension it after the first few cuts.
Keeping it sharp
A sharp chain cuts faster, puts less strain on a cordless saw, and helps reduce heat and wear.
- Keep the chain clean and lubricated. Regular cleaning and proper chain oiling help the cutters and drive links last longer.
- Touch up the cutters before the chain gets very dull. Light, regular sharpening is easier than restoring a badly worn edge.
- Avoid cutting into dirt, rocks, or buried wood. Contamination dulls a chain much faster than clean wood does.
If the saw starts producing fine dust instead of chips, pulls to one side, or needs extra pressure to cut, the chain likely needs sharpening or replacement.
FAQ
Will this fit any 10-inch chainsaw?
No. A 10-inch bar alone is not enough to guarantee fit. You also need the correct pitch, gauge, and drive-link count.
Is this chain suitable for both Black & Decker LCS1020 and WORX WG322?
Yes, those are the two specific saw models named in the listing. As always, it’s smart to confirm the chain specs on your bar or in the manual before installing.
How often should I replace the chain?
That depends on use, maintenance, and what you cut. If the chain no longer sharpens well, has damaged cutters, or stretches beyond safe adjustment, it’s time to replace it.
Do I need to do anything after installing a new chain?
Yes. Check chain tension after installation and again after the first few minutes of cutting, since a new chain may seat in and loosen slightly.
Get this chain
Ships from Amazon — check current price, stock and full fitment on the listing.
