Looking for a reliable and high-quality replacement chain for your 10 inch Greenworks pole saw?

Replacement chain fitment for select 10-inch Greenworks pole saws

This Opuladuo replacement chain is intended for certain 10-inch Greenworks pole saws, specifically the Greenworks Pro 80V PS80L00 and PS80L210, plus the Greenworks Pro 60V PS60L210, PS60L211, PS60L00, and PS60L01. If your saw uses a 10-inch bar and matches the chain specifications called for on the bar or in the owner’s manual, this replacement is designed to restore normal cutting performance with a proper fit.

A fresh chain can make a pole saw feel like new again, especially if your current chain is dull, stretched, damaged, or no longer cutting straight.

Will this chain fit your saw?

Start with the most important check: your bar length. This replacement is for a 10-inch Greenworks pole saw bar.

After that, confirm the three chain specs that always matter for fitment:

• Pitch — the spacing between chain links
• Gauge — the thickness of the drive links that fit into the bar groove
• Drive-link count — the total number of drive links on the chain

Even if a chain is labeled for a 10-inch bar, it still must match all three of those specifications to fit and run correctly. The easiest way to verify them is to:

• Check the markings stamped or printed on the guide bar
• Look in your Greenworks owner’s manual
• Compare against the specs from your original chain packaging, if available

This Opuladuo chain is listed as fitting these Greenworks pole saw models:

• Greenworks Pro 80V PS80L00
• Greenworks Pro 80V PS80L210
• Greenworks Pro 60V PS60L210
• Greenworks Pro 60V PS60L211
• Greenworks Pro 60V PS60L00
• Greenworks Pro 60V PS60L01

If your pole saw matches one of the model numbers above, that is your best fitment indicator. If your saw is a different Greenworks model, do not rely on bar length alone—confirm the chain specs before ordering.

Replacing the chain

Replacing a pole saw chain is straightforward, but safety comes first. Follow these basic steps:

1. Power the saw off completely. Remove the battery before doing any work on the bar or chain.
2. Loosen the side cover. Remove or loosen the cover that holds the bar and chain in place.
3. Take off the old chain. Lift the chain off the drive sprocket and guide bar, then remove the bar if needed to clean debris from the bar groove and cover area.
4. Install the new chain in the correct direction. Set the chain around the sprocket and along the bar, making sure the cutter edges face the proper cutting direction on the top of the bar.
5. Set chain tension. Reinstall the cover and adjust tension so the chain sits snugly in the bar groove but can still be pulled around by hand with a gloved hand.
6. Recheck before cutting. Tighten everything securely, confirm battery is still removed during inspection, then reinstall the battery and test at low load. Recheck chain tension after the first few cuts.

A chain that is too loose can derail. A chain that is too tight can wear the bar, sprocket, and motor drive components more quickly.

Keeping it sharp

A good replacement chain lasts longer when the basics are handled well:

• Keep chain oil flowing. A dry chain dulls quickly and creates excess heat. Check oil level regularly and make sure the bar is being lubricated.
• Avoid dirt and ground contact. Even brief contact with soil, sand, or hidden grit can dull cutters fast.
• Touch up the cutters early. Light, regular sharpening is usually better than waiting until the chain is badly dull, smoking, or pulling to one side.

If your pole saw starts producing fine dust instead of chips, requires extra pressure, or cuts crooked, it’s usually time to sharpen or inspect the chain and bar.

FAQ

Q: Will this fit any Greenworks 10-inch pole saw?
No. It is specifically listed for Greenworks Pro 80V PS80L00 and PS80L210, and Greenworks Pro 60V PS60L210, PS60L211, PS60L00, and PS60L01. Confirm your exact model and chain specs before purchase.

Q: Can I install this chain if my old chain is missing?
Yes, if your pole saw is one of the listed models. If not, check the guide bar and owner’s manual for the correct pitch, gauge, and drive-link count before ordering.