Ryobi 14-Inch Chainsaw Chain Fitment Guide

This 14-inch replacement chainsaw chain is made for select Ryobi saws that use a 14-inch bar. Based on the original fitment listing, it fits Ryobi RY3714, RY3714VNM, RY40503, RY40530, RY40503VNM, RY405010, RY405010BTL, RY405100, and RY405100VNM chainsaws.

If your saw is one of those exact models and it is set up with the original 14-inch bar, this is the intended replacement chain. The package includes 2 pieces of 14-inch chain, which is handy if you want a spare ready to go.

Will this chain fit your saw?

Measuring chain pitch, gauge and drive links

The quickest way to confirm fitment is to check two things:

  • your exact Ryobi model number
  • the specifications printed on the guide bar or in your owner’s manual

According to the listing, this chain is compatible with these Ryobi models:

  • RY3714
  • RY3714VNM
  • RY40503
  • RY40530
  • RY40503VNM
  • RY405010
  • RY405010BTL
  • RY405100
  • RY405100VNM

Even if your saw model appears in that list, it is still smart to verify the chain specs on the bar. Chainsaw chains are matched by more than bar length alone. A correct match requires:

  • Bar length: 14”
  • Pitch: must match your bar and drive sprocket
  • Gauge: must match the bar groove width
  • Drive-link count: must match the bar and tensioning range

Why that matters: two different 14-inch chains can look very similar but still not interchange if the pitch, gauge, or drive-link count is different. Installing the wrong chain can lead to poor cutting, tensioning problems, excess wear, or unsafe operation.

The easiest place to check is the stamp or label on the guide bar. Many bars list the pitch, gauge, and drive-link count directly. If those markings are worn off, check your Ryobi manual for your exact model number. When the saw model and the bar specs agree with this replacement, you can order with much more confidence.

Replacing the chain

Fitting the chain onto the bar and sprocket

Always replace the chain carefully and with the saw fully powered down.

  1. Turn the chainsaw off and disconnect the power source. For cordless models, remove the battery. For gas models, make sure the engine is off and cool.
  2. Loosen and remove the side cover, then back off the chain tension so the old chain can be lifted off the bar and sprocket.
  3. Place the new chain onto the drive sprocket and around the guide bar, making sure the cutter direction is correct. The cutting edges on the top of the bar should face forward toward the bar nose.
  4. Reinstall the side cover loosely, then adjust chain tension until the chain sits snugly in the bar groove but can still be pulled around by hand with a glove.
  5. Tighten the bar nuts or cover hardware securely, then recheck tension before use.
  6. Run the saw briefly, stop it, and check tension again. A new chain can seat in quickly and may need a minor retension.

A properly tensioned chain should not sag under the bar, but it also should not be so tight that it binds.

Keeping it sharp

Sharpening a chainsaw chain cutter

A sharp chain cuts faster, puts less strain on the saw, and is generally safer to use.

  • Avoid letting the chain touch dirt, rocks, or the ground. Even a brief contact can dull cutters quickly.
  • Keep chain oil topped up and make sure the bar is oiling properly. Good lubrication helps reduce heat and premature wear.
  • Touch up the chain early instead of waiting until it is very dull. If the saw starts making fine dust instead of chips, pulling to one side, or needing extra pressure, it is time for maintenance.

It also helps to rotate between the two included chains so you can clean or sharpen one while using the other.

FAQ

Does this chain fit every Ryobi 14-inch chainsaw?
No. It is listed for specific Ryobi models only: RY3714, RY3714VNM, RY40503, RY40530, RY40503VNM, RY405010, RY405010BTL, RY405100, and RY405100VNM. You should still confirm the bar specs before ordering.

How many chains are included?
The package includes 2 pieces of 14-inch chain.

If my bar says 14 inches, is that enough to confirm fit?
Not by itself. You also need the correct pitch, gauge, and drive-link count to match your saw and bar.

Can I install this chain on a different bar length?
No. This replacement is intended for a 14-inch setup. Chain length and fit are tied to the bar size and the exact chain specifications.

Get this chain

Ships from Amazon — check current price, stock and full fitment on the listing.

Buy on Amazon